The E-Props Company
The E-PROPS Company
195, Route de l'Aviation
ZI Aérodrome de Sisteron
04200 VAUMEILH - France

The best way to reach our team is by email :

E-PROPS : Strong Propellers

The E-PROPS are ultra-light and quiet propellers, and they have a very good efficiency. They also are very strong propellers.


1- Ultra-Light and Strong : how is it possible ?
2- Why the E-PROPS are very strong propellers ?
3- E-PROPS load test

1- Ultra-Light and Strong : how is it possible ?

In the collective unconscious : a strong product must be heavy, and a heavy product is strong.
But this idea is really too simplistic. A material is governed by different criteria; strength is only one of them, and there are many types of "strength" : compressive, tensile, flexural, yield...
The use depends on the criteria which are the most important for the product.
For a specific application, a lighter material can be better than a heavier one.
For example, steel is not adapted to make a propeller for big airplanes. It would be far too heavy. So manufacturers are manufacturing such propellers in aluminium, 2.8 time lighter than steel, and which have quite the same ultimate tensile strength (about 500 MPa).
Steel is heavier than aluminium, but it is absolutely not the best material to make propellers for big aircraft.

For paramotors, the propellers are not made in aluminium. In this case, aluminium is not the best material.
Engines have a maximum value of Moment of Inertia.
A 2-blade aluminium propeller diameter 125 cm would weight more than 2,5 kg. As a reminder, the same propeller E-PROPS PLUG'n'FLY weights less than 500 gr... 5 times less !
The Moment of Inertia of such aluminium propeller would be far too high and this type of propeller would break the reducer in a couple of hours.

Wood and composite are lighter than aluminium, and are the best materials to make strong paramotors propellers.

Composite materials are the best materials for aeronautics, especially carbon, because they are very light at the same time as very strong.
Today, aircraft structures are commonly made up of 50 to 70 % composite materials, including airliners : the Boeing 787 Dreamliner is made of 50 % composite materials, and the Airbus A350 of 53%.

composite in airliners

There are many types of composite materials and many different manufacturing process.
Examples of tensile strengths :
- fiberglass : 2.600 MPa
- carbon : 4.000 MPa
- epoxy resin : 80 MPa

To make very strong carbon parts, the most important is to have the maximum of fibers and the minimum of resin. Fibers is 50 times more resistant than resin.

E-PROPS RTM manufacturing process allows to have the hightest fibers ratio on ultra-light parts. Fiber ratio is : carbon fibers / epoxy resin.
Parts made by E-PROPS have a very high carbon fiber ratio : 63% (which is exceptional).
For example, a 2 glued half-shell blade has a fiberglass fiber ratio of about 30%.
The gap is very important, because of the ratio, and because the carbon fibers are more resistant than glass fibers.

Competing composite propellers are heavier, because usually made in fiberglass, with far more resin, using different process which allows only a very low fibers ratio. They are heavier, yes, but absolutely not stronger !

In conclusion, the full carbon E-PROPS propellers are stronger than competing composite propellers.

2- Why the E-PROPS are very strong propellers ?

The E-PROPS are made in carbon braid, with continue fibers between upper and lower surfaces of the blade (very high resistance).
The carbon is the material whichs presents by far the best compromise rigidity / weight for long parts, as blades.
The exceptional carbon fiber ratio (63%) allows to make ultra-light parts.
An internal spar strongly reinforces the blade.

The HCF (Helical Continuous Fibers) process, specifically designed by E-PROPS, ensures an exceptional strength of the 100% carbon + epoxy resin blade, from leading edge to trailing edge, from blade's foot to tip.
The carbon fibers ratio of the E-PROPS is very high (63%). It is very important to have the maximum of carbon fibers and the minimum of epoxy resin.
Contrary to the traditional "2 glued half-shell" process (used by many propellers manufacturers), fibers are continuous between the intrados and the extrados (carbon braid, made as a sock).
The mechanical resistance of the blade is increased and becomes very high : no slightest risk of blade's explosion by delamination of the leading edge, no possible cracks on the blade or on the hub.

The leading edge of all E-PROPS propellers is reinforced :
- or with a Nanostrength® shock additive (ARKEMA product: nanostructured additive with high kinetic energy absorption capacity): E-PROPS injects this additive into the resin all along the leading edge of the blades. This protection, very resistant, does not induce any detachment and no electrolytic torque. See Nanostrength protection
- or with Titanium metal leading edge protection : the ideal material for blade leading edge thanks to its mechanical characteristics. See Titanium leading edge protection

The E-PROPS are very light. They are designed and manufactured with continuous fibers, and not in 2 glued half-shell (as many competing propellers), with a very high carbon fibers ratio, and are more resistant than heavier fiberglass propellers.


3- E-PROPS load test

All E-PROPS propellers are tested to see how they resist at centrifugal load test.
Centrifugal load tests are very important test in order to define the mechanical resistance of the propellers.
In certified aviation (in Europe), they are defined by EASA Certification Specifications for Propellers (CS-P).
The aircraft propeller must be tested for a period of one hour to a load equivalent to twice the maximum calculated centrifugal load.
The propeller must show no failure or permanent deformation.
E-Props has developped an hydraulic load test bench : high : 3,5 m, weight : 300 kg, and maximum load 40 tonnes. All propellers models are tested on this bench.

Example :
The maximum centrifugal load on a fixed pitch propeller at 3.000 tr/min has been calculated by the LmPTR© software : 7.000 N (714 kg).
In this case, the CS-P for certified propellers says that the propeller must be tested for a period of one hour to a load of 14.000 N (1,4 tonnes).
1/ Application of a load of 28.000 N (2,9 tonnes) during 1 hour. Then control : nothing to report
2/ The load increases at 4.000 N per minute
=> Break of one blade at load 32.500 N (3,3 tonnes)
The maximum centrifugal load at 3.000 RPM is 7.000 N, so the safety coefficient of centrifugal load is 4,6.

The propeller can hold 4 times the maximal load during 1 hour without any damages.

The EASA CS-P for certified aircraft propellers says that the propeller must be tested for a period of one hour to a load of 14.000 N.
The propeller has holded a load of 28.000 N during 1 hour, it means twice what is asked by EASA CS-P for certified propellers.


English Francais
Fixed Props for engines 7-50 kW dia 115 to 160 cm
Adjustable Props for engines 50-168 kW dia 120 to 209 cm